Click Here

 

Are you in search of selective information about How to Install a Bathtub?

Installing a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is easily obtainable, the task can move quickly; if you need to open a wall surface to get rid of the old bathtub and also position the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to vacate the old tub and set in the brand-new one. Make sure you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you might need a professional plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your bathroom if you have actually currently gotten a new bathtub as well as don't require to alter the setup of your previous supply of water pipes.
Your devices and product list ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipes. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines are in place between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former type ought to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Mounting the Tub

Using the two wooden boards under its feet, put the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub up until the spirit level reads degree.
To set up taps, fit the bottom of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the supply of water and also inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Fill up the bath tub as well as also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub ought to wait up until the tub has actually been utilized a minimum of when as this will certainly resolve it right into its last placement.

 

 

Getting ready for the Setup

First of all, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must now be ready to be suited its final position.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can split rather very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I have been very interested by Installing A Bathtub and I hope you enjoyed reading the new page. So long as you enjoyed our post plz remember to pass it around. Bless you for your time. Kindly check up our blog back soon.

Expert attention offered.